Latest Posts

How to Fix Creaky Floorboards (From Above and Below)

Newly laid oak floor running through an open-plan kitchen area towards a large floor-to-ceiling window

There is always one board. It speaks up the moment someone crosses the landing at night, and tiptoeing never helps. The good news is that most creaky floorboards are straightforward to fix. A creak usually means a board is rubbing against its neighbour or moving on the joist beneath it, so the fix is to find the exact spot, check what is under it, and then fix the board tight to the joist from above, or support it from below if you can reach the underside.

One thing before you pick up a drill: a creak is not the same as a floor that feels springy or sags underfoot. That needs a professional to look at it, and we explain the signs further down.

At Silver Lining Floor Care, we lift and repair original floorboards in London period homes every week. This guide follows the method we would want you to use, including the safety checks that most guides leave out. It covers how to fix a squeaky floor from above and below, under carpet, and upstairs where there is no way in from underneath.

 

Why Do Floorboards Creak?

Knowing the cause helps you choose the right fix. Most creaks come down to a handful of things:

  • Dry timber. Central heating dries boards out, and as they shrink they loosen. That is why creaks often start in autumn and winter.
  • Loose fixings. In older suspended timber floors, the nails holding the boards down work loose over time through ordinary wear and tear.
  • Rubbing. Boards chafe against each other, or against pipes and fittings running beneath them.
  • Gaps and movement. A board that no longer sits snugly on its joist will move underfoot, and so will a joist that has shifted or been notched to make room for pipes and cables. Wide gaps between the floorboards add to the movement, which is why filling gaps in floorboards is often part of the same repair.

If your floor is made of chipboard sheets rather than boards, as in many newer builds, the squeak usually comes from the sheet edges rubbing or the fixings working loose. The principle is the same: get it fixed tight to the joist.

 

How to Find the Creak (and What Is Under It)

Walk the floor with a helper. One person walks slowly across the room while the other listens and marks each board that creaks with a pencil or masking tape. Try different directions, because some boards only creak when the weight comes from one side.

Next, find the joists. These are the timbers the boards are fixed to, and a fix only works if the screw goes into one. Look for lines of nail heads running across the boards, use a stud finder, or lift a board and look.

Check for Pipes and Cables Before Any Screw Goes In

This is the step that matters most. Heating pipes, water pipes and electric cables often run under floorboards, and they commonly pass through notches cut into the tops of the joists, just beneath the boards. A screw in the wrong place can puncture a pipe or damage a cable.

  • Scan the area with a pipe and cable detector before you drill. It helps, but treat it as a guide, not a guarantee.
  • Look for signs that the boards have been lifted before, such as damaged edges or extra fixing holes.
  • Never screw through a board near a radiator pipe run without lifting it first.
  • If you are unsure, lift the board and look.

Electrical Safety First, the UK electrical safety charity, describes drilling, nailing or screwing into hidden cables as a common DIY error. The same risk applies beneath your floor.

 

How to Fix Creaky Floorboards From Above

For most homes, this is the main method. You will need a drill, a pilot drill bit, a countersink bit, flooring screws and your pipe and cable detector.

  1. Mark the joist. Find the joist nearest the creak using the nail line or a stud finder, and mark it.
  2. Check for pipes and cables. Scan the spot, and lift the board if there is any doubt.
  3. Drill a pilot hole. Drill through the board and a little into the joist, using a bit slightly narrower than the screw so the board does not split. Then countersink so the head sits just below the surface.
  4. Drive in a flooring screw. Choose one long enough to bite well into the joist (50mm is a common length for a standard board). Screw into the joist, not between joists, where it would hold nothing.
  5. Work along the board. If the board moves along its length, add a screw where it crosses each joist. Check the ends of the board too, as loose ends are a common source of noise.
  6. Finish the surface. On bare boards, fill the countersunk holes with a matching filler. Under carpet, you can leave them.

Use proper flooring screws, not drywall screws, which are brittle and not made to hold timber down. Screws also give a more lasting fix than nails, since it was the nails that worked loose in the first place. And leave the WD-40 in the cupboard: it can stain bare timber and will not stop a board that is loose on its joist.

A Quick Fix for Boards That Rub: Talc or Graphite

If two boards are simply rubbing along their edges, sprinkle talcum powder or powdered graphite along the joint and brush it in so it works down between the boards. It can quieten things quickly, but it is only a temporary fix. If the creak comes back, the board is probably loose on the joist and needs screwing down.

Replace a Split or Worn Board Instead

If a board is split or badly worn, screwing it down only holds the damage in place. Replace it instead. On period floors, a modern pine board rarely blends in, which is why we use reclaimed pine of a similar age when we repair original floorboards.

 

How to Fix Creaky Floorboards From Below

If you have a cellar or underfloor access on the ground floor, you can often fix the creak without touching the surface of the floor. Ask a helper to walk across the room above while you watch from below with a torch. You are looking for the point where a board moves against the joist or drops away from it. Check for pipes and cables as you go.

  • Wedges or shims. Tap a small wooden wedge, coated in wood glue, into the gap between the joist and the board. It should fill the gap snugly. Do not force it in so hard that it lifts the board, or you will swap a creak for an uneven floor.
  • Blocking. Where a joist has twisted or moved, a short block of timber fixed between neighbouring joists can steady the floor and reduce movement.
  • Adhesive. A bead of construction adhesive where the board meets the joist can help hold a board that has lost contact, as long as it is supported while the adhesive cures.

 

How to Fix Creaking Floorboards Under Carpet

Lift the Carpet if You Can

The most reliable way to stop creaking floorboards under carpet is to lift the carpet where you can. Release a corner or a section from its gripper rods, fold it back, and lift the carpet underlay. You can then see the boards, check for pipes and cables, and fix the board to the joist exactly as described above before laying the underlay and carpet back. You often only need to lift one side of the room, not the whole carpet.

Fix a Squeaky Floor Under Carpet Without Removing It

If you do not want to lift the carpet, snap-off screw kits let you fix a loose board through it. The kit helps you locate the joist, and you drive in a screw that snaps off just below the carpet fibres. They have limits:

  • You cannot see what is under the carpet, so the pipe and cable check depends entirely on your detector. The Health and Safety Executive reminds anyone drilling to check around the job, because electrical cables can run within walls, floors and ceilings.
  • They tighten a board but will not repair a split or worn one.
  • If the creak returns after a few screws, stop adding more and lift the carpet to see what is really going on.

 

Fixing Creaky Floorboards Upstairs

Upstairs floors are the awkward ones. There is a ceiling below, so you cannot wedge or support the board from underneath, and the fix has to be done from above. Creaks here are often caused by boards resting on pipes or cables that cross the joists, which is another reason the safety check comes first.

  1. Find and mark the board. Use the helper method, then mark the nearest joist.
  2. Lift the carpet and underlay around the spot.
  3. Lift the board if you can. Square-edged boards can be lifted with care. Tongue-and-groove boards are harder to lift without splitting them, so stop if you are not confident.
  4. Check what is underneath. Look for pipes or cables running across the joists, and for notches cut into the tops of the joists.
  5. Re-fix the board to the joist with flooring screws, countersunk, then refit the underlay and carpet.

If a board is sitting hard on a pipe or cable, do not screw it down tighter. That needs more than a screw, and it is worth having a professional look at it.

 

When Creaking Means a Structural Problem

A creak on its own is rarely dangerous. It is usually a sign of movement between a board and its joist, and many older homes have a few. But some signs point to a structural problem rather than a loose board:

  • A springy or sagging floor. If the floor bounces or dips noticeably underfoot, the problem is not the board.
  • Soft or damp boards. Timber that feels soft, spongy or damp suggests moisture, and the cause needs finding.
  • Cracked or heavily notched joists. If you lift a board and see a joist that has cracked, or deep notches cut into it, get it checked.
  • A creak that spreads. If the noise is getting worse or moving across the room, something is shifting.

If you notice any of these, do not keep adding screws. Stop and get a professional to look at the floor.

 

DIY or Call a Professional?

Fixing one or two loose boards is a reasonable DIY job if you can reach them, you have checked for pipes and cables, and the boards are in good condition. Call a professional if:

  • the floor is upstairs and the boards will not lift easily
  • there are pipes or cables in notches across the joists
  • boards are split, worn or damaged, or need replacing
  • you do not want to lift a fitted carpet
  • you see any of the warning signs above
  • the creak keeps coming back

A professional floorboard repair starts with a detailed inspection. We lift the boards, check the joists and any services beneath them, then re-fix or replace boards as needed, matching the original pine so the repair blends in. If your floor is an original Victorian one, our Victorian floorboard sanding service can then bring the boards back to their best.

The cost depends on how many boards are affected, how easy the floor is to reach, and whether any need replacing. If you think boards may need replacing rather than re-fixing, our guide to how much it costs to replace floorboards explains what affects the price.

 

Fix It Once, and Fix It Properly

To recap: find the creak, check what is under it, fix the board tight to the joist with flooring screws, and call a professional if the floor feels springy or you cannot safely reach the problem.

If you would rather leave it to people who lift and repair floorboards every week, we can help. Send us photos of the floor and your postcode, and we will quote for floorboard repairs in London.

Creaking on the stairs rather than the floor? Our guide to how to fix squeaky stairs covers that.

How to Clean Vinyl Flooring: The Complete Guide to a Deep Clean